Call Today

 

What are your opinions about Installing A Bathtub?

Installing a bath tub isn't exactly rocket science, but it does require solid plumbing, woodworking, and sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is conveniently easily accessible, the project can relocate immediately; if you have to open a wall surface to get rid of the old tub and position the brand-new tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and also set in the brand-new one. See to it you have actually qualified on your own for the job as well as are comfortable trying it. As opposed to employing a contractor to take control of a halfway-completed job, it is better to think about utilizing one prior to you begin. Opportunities are you may need a professional plumber to make tube connections.
This article will assist you install a new bathtub in your shower room if you have already acquired a brand-new bathtub and also do not need to alter the arrangement of your previous water system pipelines.
Your devices and product list must comprise the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Planning for the Installation

To start with, the supporting frame provided with the bathroom should be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the faucet includes a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets system to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its final position.

 

 

Removing Old Taps

If you need to change old taps with new ones as a part of your installment, then the first thing you ought to do is detach the water supply. After doing so, activate the taps to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing taps can be fairly troublesome due to the restricted accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the remaining water that will come from the pipelines. As soon as the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Mounting the Bath tub

Utilizing both wood boards under its feet, put the bath tub in the called for placement. The wooden boards are helpful in evenly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto four small factors.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level and also adjusting the feet on the bathtub until the level reads level.
To set up faucets, fit all-time low of the furthest adaptable tap port to the ideal supply pipe by making a compression join; after that do the exact same for the various other tap.
Activate the water and inspect all joints and new pipework for leaks and also tighten them if essential. Fill up the bathtub as well as also inspect the overflow electrical outlet and the regular outlet for leaks.
Finally, fix the bathroom paneling as described in the manufacturer's user's manual. Tiling and securing around the tub must wait up until the tub has actually been made use of at least when as this will settle it into its last position.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in location in between the tap and the sink. Protect the faucet in place with the supplier supplied backnut. Once the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The previous type ought to be connected to the faucet finishes initially, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Bath tub

In the location where the bathroom satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to break a stiff seal, causing the water to penetrate the wall in between the bath and also the tiling, resulting in problems with moisture and also feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures and installations. They are offered in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to permit the movement experienced when the tub remains in use. The sealant can crack rather very early if you do not take into account this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily available on the marketplace. It is a good idea to fit the floor tiles utilizing water-resistant or waterproof adhesive and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We hope you liked our part on Installing A Bathtub. Thank you for finding the time to read our short article. Those who enjoyed reading our blog posting please be sure to share it. Thanks a lot for your time. Visit again soon.

Leaks? Contact us!